Drawing no of fixed width rectangle between two selected points

[Halsy]

i have to draw fixed width rectangle which is 600,500,450,400,360,350,320,300,280,275,270,260,250,230,225,220,210,200,195,190,185,180,175,170,165,155,150,145,140,135,130,125,120,115,110,105,100 and between two selected point whether on  axis or y axis 

[CADTutor]

I think the community may need a little more information. It's not exactly clear what you are asking and what that multi-dimensional coordinate is for.

[Halsy]

if i select 2 point which is shown in image then rectangle of fixed with which is emption early has to come and after selection user has to give height of that rectangle

which is on both x axis and y axis

[myloveflyer]

21 hours ago, Halsy said:

我必须画出固定宽度的矩形，这是600,500,450,400,360,350,320,300,280,275,270,260,250,230,225,220,210,200,195,190,185,180,175,170,165,155,150,145,140,135,130,125,120,115,110,105,100，在两个选定的点之间，无论是在轴上还是y轴上。

Please provide test DWG

[Dadgad]

At first glance my thought was should we be using units of measure light years?

[Halsy]

if i select 2 point which is shown in image then rectangle of fixed with which is emption early has to come and after selection user has to give height of that rectangle

which is on both x axis and y axis

[devitg]

Sad to say , ACAD can not edit a image. Please up load your DWG -

 

Other fact what could be the distance from point-1 to point-2? 

 

How it will be discriminated or decided which measure to take 

 

The horizontal have 3 x 600 + 1 x 500 + 1x 170 . 

Or could it be 2 x 600 + 2 x 300 + 1x250+  +1x120+ 1x130+ 1 x 170 

Please set up the formation rule. 

 

 

 

 

[BIGAL]

This has been discused in great length over at forums/autodesk and I think is posted here now as there ws not a final solution provided.

 

The issue with the solution was the random way a final panel is chosen it was like I want an answer from the 5 different combinations that I could use but the code has to pick the correct one which seems totally random.

 

Again look at  this before replying https://forums.autodesk.com/t5/visual-lisp-autolisp-and-general/divding-two-points-into-specifi-width-and-height-of-rectangle/td-p/10533944/page/2 its up to 24 replys.

[Halsy]

if i select 1st point and 2nd point on screen then user has to give a height of that rectangle then rectangle of width 600 ,500,450,400,360,350,320,300,280,275,270,260,250,230,220,210,200,195,190,185,180,175,,170,165,160,155,150,145,140,135,130,125,120,115,110,105,100 has to come where maximum number of rectangle of width 600 has to come then rest of above list

Drawing1.dwg

[Halsy]

where the length is taken between two selected points

[devitg]

so the distance between 2 point can    always  hold the sizes show , only will end  to 5 or 0 ?

[Halsy]

The distant between 2 points may be end with 0 or 5 

[BIGAL]

Devitg "Please set up the formation rule." Did you read all the comments at forums/autodesk to random an answer to code.

Edited August 24, 2021 by BIGAL